US: SAE Signal Preemption - WAVE TCP

Description:

This solution is used within Canada and the U.S.. It combines standards associated with US: SAE Signal Preemption with those for V-X: WAVE TCP. The US: SAE Signal Preemption standards include upper-layer standards required to implement signal preemption and priority information flows. The V-X: WAVE TCP standards include lower-layer standards that support connection-oriented vehicle-to-any communications within ~300m using the Transmission Control Protocol (TCP) over Internet Protocol version 6 (IPv6) over IEEE WAVE in the 5.9GHz spectrum.

Comm Profile: V-X: WAVE TCP

Level	Doc #	Standard	Description
Access		Bundle: WAVE - Subnet	A bundle of standards specifying the lower layers of the reference communications model for the US DSRC environment.
Security		Bundle: IEEE 1609.2	A bundle of standards that groups a set of IEEE security standards together for easy reference.
TransNet		Bundle: IPv6 for WAVE	A bundle of standards that identifies the RFCs that define how to use IPv6 over a WAVE (DSRC) environment. This group of standards is identified as a part of IEEE 1609.3.
TransNet	IEEE 1609.3	IEEE 1609.3 WAVE - Networking Services	This standard defines the network and transport layer options for the WAVE environment. The standard defines three options: a bandwidth efficient single-hop solution known as WSMP, UDP/IP, and TCP/IP. It has been harmonized with ISO FNTP and FSAP - a common message format specified in ISO 16460.
TransNet	IETF RFC 9293	IETF RFC 9293 TCP	This document specifies the Transmission Control Protocol (TCP). TCP is an important transport-layer protocol in the Internet protocol stack, and it has continuously evolved over decades of use and growth of the Internet. Over this time, a number of changes have been made to TCP as it was specified in RFC 793, though these have only been documented in a piecemeal fashion. This document collects and brings those changes together with the protocol specification from RFC 793. This document obsoletes RFC 793, as well as RFCs 879, 2873, 6093, 6429, 6528, and 6691 that updated parts of RFC 793. It updates RFCs 1011 and 1122, and it should be considered as a replacement for the portions of those documents dealing with TCP requirements. It also updates RFC 5961 by adding a small clarification in reset handling while in the SYN-RECEIVED state. The TCP header control bits from RFC 793 have also been updated based on RFC 3168.

Data Profile: US: SAE Signal Preemption

Level	Doc #	Standard	Description
Facilities	SAE J2735	SAE J2735 DSRC Message Set	This standard defines the data and messages for use in DSRC (i.e., V2V, V2I, and V2D) applications. The SAE J2945 series defines additional requirements on how to use these messages.
Facilities	SAE J2945	SAE J2945/0 DSRC Common Design Elements	This standard defines cross-cutting material which applies to the J2945/x series including generic DSRC interface requirements and guidance on Systems Engineering (SE) content.
ITS Application Entity	CTI 4501	CTI 4501 CI Implementation Guide	This Connected Intersection (CI) Implementation Guide defines the key capabilities and interfaces a connected signalized intersection must support to ensure interoperability with production vehicles for state and local IOOs. A connected intersection is defined as an infrastructure system that broadcasts SPaT, MAP, and position correction data to vehicles.
ITS Application Entity	ISO 19091	ISO 19091 V2I for signalized intersections	This technical specification defines messages and related data structures and data elements for the following exchanges between roadside equipment and vehicles: 1) Definition of the SPaT (signal phase and timing) message transmitted from a traffic controller that describes the state of the signals, signal timing as necessary to support the applications identified herein; 2) definition of the MAP message (which include the definition of motorized lane, vehicles, busses, trams, bicycle, pedestrian crosswalks, etc.); and 3) definition of the messages (SRM, SSM) to be exchanged between an intersection traffic controller and approaching vehicles to support priority treatment as might be expected for emergency response , freight transport, and public transport vehicles to improve safety.
ITS Application Entity	SAE J2735	SAE J2735 DSRC Message Set	This standard defines the data and messages for use in DSRC (i.e., V2V, V2I, and V2D) applications. The SAE J2945 series defines additional requirements on how to use these messages.
ITS Application Entity	SAE J2945/B	SAE J2945/B Signal Intersection Applications	This document provides guidance on usage of SAE J2735 and other related information for signalized intersection applications. The document focuses on how to use SPaT and MAP messages to support signalized-intersection applications. In general, implementation guidance is necessary to achieve interoperability by addressing the requirements for the options for both over the air dialogs and message contents, and to support larger intersection maps This document also addresses using Signal Request & Signal Status messages corresponding to vehicle functionality and approaches to traffic signal priority/pre-emption (TSP), including three different methods for implementing TSP over the air. The project is complementary to the connected intersections project being performed by ITE.

Readiness Description:

Many serious issues. This category includes solutions that have not been standardized, or do not have a basic level of interoperability or security. Consider selecting a different communications solution or if this is not possible (eg. a pilot of a new application that has not been standardized), take additional measures to provide an acceptable level of security or interoperability.